Best Hard Hat Sun Shades

Top pick: Ergodyne Chill-Its 6660 brim and neck shade

For a cap-style hard hat in direct sun, buy the Ergodyne Chill-Its 6660. One accessory shades your face and the back of your neck. It is the only shade here whose maker publishes a UPF figure (UPF 50+), and its 19.5 in neck panel is the widest of the three Ergodyne shades listed. It costs about $9-15 in retail listings.

Get Ergodyne Chill-Its 6660

Ergodyne’s figures: the brim is 3.25 in (8.3 cm), and the neck panel is 9.75 in (24.8 cm) long by 19.5 in (49.6 cm) wide. The fabric is 100% polyester, rated UPF 50+. A plastic ring keeps the brim from drooping. An elastic rim stretches over the shell, and hook-and-loop straps fasten to the suspension; Ergodyne says it “attaches securely to most hard hats”. It comes in hi-vis lime and hi-vis orange. Ergodyne’s care instruction is hand wash and hang dry. Ergodyne posts a California Proposition 65 warning for this product.

The 19.5 in width is what puts it first. Ergodyne says the wide panel extends down for complete back-of-neck coverage. Compare Ergodyne’s 14.75 in for the 6670CT cooling shade and 12.5 in for the neck panel on the 6717 pad. The low-sun hours at the start and end of a shift hit the side of the neck, and that is the skin a narrow flap leaves out.

Who should not buy it:

Get Ergodyne Chill-Its 6670CT Get Radians SE Treated Hi-Vis Neck Shade

These picks were not tested. The ranking comes from the makers’ published specifications and retail listings, and the list gives no scores.

Runner-up for heat: Ergodyne Chill-Its 6670CT cooling neck shade

If the problem is heat stress rather than sunburn, buy the Ergodyne Chill-Its 6670CT instead of the 6660. It is a neck-only shade made of polyester with a PVA (polyvinyl alcohol) cooling layer. Run it under water for one minute, and the evaporating water cools the back of the neck. Ergodyne rates it at up to 4 hours of cooling per soak, and you re-wet it to start again. Ergodyne gives the panel as 10.5 in (26.6 cm) long by 14.75 in (37.5 cm) wide and says it covers the back of the neck and the ears. Hook-and-loop straps fasten it to the suspension of most hard hats. Ergodyne says it is machine washable and should air dry. Ergodyne posts a California Proposition 65 warning for this product. Retail listings put it at about $11-18 in hi-vis lime.

What you give up for the cooling: there is no brim, so the face gets only what the hard hat’s own peak gives it. Ergodyne also publishes no UPF number for it, only that it shields the neck from UV. Evaporative cooling works best in dry air, where water evaporates fast. On a humid Gulf Coast site, the 4-hour figure is a ceiling. And because the panel only cools while it is wet, it needs water on hand to re-soak.

Who should buy the 6670CT over the 6660: roofers, paving crews and anyone wearing a full-brim hard hat that already shades the face. If you need cooling across the torso rather than just the neck, compare cooling vests at best cooling vests for construction. A neck shade cools a few square inches of skin, and a vest cools the whole chest and back.

The rest, ranked: Radians, OccuNomix and the budget Ergodyne pad

3. Radians RHHS-01 Collapsible Hard Hat Shade: best for full-brim hats and for packing away. Radians no longer lists the RHHS-01: its product page returns not found, and Radians’ cooling range now shows the RHHS-02. Retailers still sell it. Radians’ archived page says the Radians RHHS-01 shields the face and neck, fits most full-brim and half-brim (cap-style) hard hats, and collapses into a pouch attached to the shade. Radians’ archived page carries a California Proposition 65 warning (cancer and reproductive harm). Retail listings give its size as 17.13 in by 9.65 in and its weight as 0.28 lb, in hi-vis green or orange. It is about $11 at safety-supply listings. Buy it over the 6660 if you wear a full-brim hat, since Radians states full-brim fit and Ergodyne does not. Also buy it if the shade comes off when you go indoors and you want somewhere to stow it. Radians publishes no UPF figure for it, so the 6660 remains the pick for anyone choosing on UV rating.

Get Radians RHHS-01

4. OccuNomix 899 Stow-Away Hard Hat Shade: best for crews who want cotton, not polyester. The OccuNomix 899 is a sunshade that circles the hard hat, held open by a wire spring around the rim. OccuNomix says it fits most hard hats including full-brim, and that it folds into a 6 in round pouch. The navy, white and khaki versions are cotton twill. The hi-viz yellow version is polyester oxford. OccuNomix lists it at about $17 on its own store. Choose the cotton colors if synthetic fabric against your neck bothers you in heat. OccuNomix says the shade at the back of the neck “protects from UV rays” but gives no UPF number. And navy or khaki are not high-visibility colors, which matters for anyone working near moving equipment.

Get OccuNomix 899

5. Ergodyne Chill-Its 6717 Cooling Hard Hat Pad and Neck Shade: the cheapest way to cool your neck. The Ergodyne Chill-Its 6717 combines a liner pad and a neck shade, attached to the suspension with two hook-and-loop straps. Ergodyne describes it as cotton with acrylic polymer crystals. Ergodyne posts a California Proposition 65 warning for this product. You soak it in water for 2 to 5 minutes, and the crystals hold the water for up to 4 hours of cooling. Ergodyne warns not to over-activate it: that may cause the pad to “plump up” to a size where it is no longer able to be comfortably worn. Ergodyne’s size chart gives 12.75 in by 14.25 in, and its feature list gives the neck shade as 9.75 in by 12.5 in. It costs about $5-9, which suits supervisors buying for a whole crew. The trade-offs against the 6670CT: a narrower neck panel, a solid blue color that is not hi-vis, and crystals that need a longer soak than the PVA shade. Buy the 6717 when price per head matters more than coverage.

Get Ergodyne Chill-Its 6717

6. Radians SE Treated Hi-Vis Neck Shade: the specialist pick for flame exposure. Radians lists the Radians SE Treated Hi-Vis Neck Shade as self-extinguishing treated 100% polyester mesh that meets ASTM D6413. It fits both cap-style and full-brim hard hats and comes in hi-vis green (NSG-UNIV) or orange (NSO-UNIV) with contrasting trim. Radians posts a California Proposition 65 warning (cancer and reproductive harm) for it. It is the only shade here with a published flame-resistance claim. That makes it the one for welders and anyone near sparks. Radians says its self-extinguishing treated polyester is not for use where an arc flash or flash fire hazard exists. Everyone else gets more coverage from the 6660.

Brim shade, neck flap or cooling insert: how the three types work

Hard hat sun shades come in three constructions, and each one covers a different part of the head.

What more money buys is narrow. Every pick here costs under about $20, and the spread is driven by cooling material, fabric (cotton twill versus polyester) and stow-away pouches, not durability ratings. No maker in this list publishes a wash-cycle life or a fade rating. The 6717 at about $5-9 and the OccuNomix 899 at about $17 do different jobs. The 899 is not a better version of the 6717.

What is not worth the money: a cooling shade bought for sun protection. Neither the 6670CT nor the 6717 publishes a UPF number. Damp fabric also generally lets through more UV than dry fabric. If sunburn on the neck is the complaint, the dry, UPF 50+ rated 6660 is the purchase, and spending more on cooling does not improve sun protection.

Fit: cap-style versus full-brim shells and the suspension

Hard hats sold to ANSI/ISEA Z89.1 come in two shapes that decide which shade fits: cap-style, with a short front peak, and full-brim, with a brim all the way around. The makers state fit as follows:

The attachment method matters as much as the shell shape. An elastic or wire rim grips the outside of the shell, so the shade stays put even when the hat is off your head. Suspension straps hold a shade in line with the headband, which keeps a neck panel centered when you turn your head. The 6660 uses both, and that is part of why it ranks first. The 899 relies on its wire spring rim, and OccuNomix says it easily folds away into its pouch.

Three interference points to plan for:

No maker on this list publishes a compatibility chart naming specific hard hat models. For an unusual shell, such as a vented Type II helmet with a rear dial, the shell’s brim diameter and whether the suspension has exposed straps decide the fit.

UPF, hi-vis color and flame resistance: what the labels prove

UPF. UPF (ultraviolet protection factor) is a fabric rating tested under AATCC TM183 and labeled under ASTM D6603 in the US. UPF 50+ means no more than 1/50 of UV radiation passes through, so at least 98% is blocked. Of the six picks, only the Ergodyne Chill-Its 6660 carries a published UPF 50+ rating. Radians, OccuNomix, and Ergodyne for its cooling shades all describe UV protection without a UPF number. That is a real difference, not a labeling quirk: an unrated fabric may still block a lot of UV, but nothing on the label lets you compare it.

Hi-vis color. Lime, orange and yellow make you easier to see. But none of these shades claims ANSI/ISEA 107 high-visibility certification, which applies to garments with set amounts of background and reflective material. A hi-vis shade adds to a compliant vest and does not replace it. The OccuNomix 899 in navy or khaki and the Ergodyne Chill-Its 6717 in blue add no visibility at all.

Flame resistance and arc flash. ASTM D6413 is a vertical flame test that measures char length and afterflame on fabric. The Radians SE Treated Hi-Vis Neck Shade meets it, so the treated mesh self-extinguishes once a spark or flame is removed. That is the right property for welding areas and grinding. ASTM D6413 is not an arc rating, though. Radians publishes no ATPV or EBT value in cal/cm², and NFPA 70E arc-flash PPE is selected by arc rating. Radians says its self-extinguishing treated polyester is not for use where an arc flash or flash fire hazard exists. The 6660 and 6670CT (polyester, per Ergodyne) and the RHHS-01 have no flame-resistance claim. Keep them away from hot work and anywhere that requires arc-rated clothing.

Upkeep, lifespan and the mistakes buyers make

Care instructions differ by construction, and getting them wrong shortens a shade’s life:

Common mistakes, in the order they cost you:

  1. Buying a cooling shade to stop sunburn. Neither evaporative pick publishes a UPF number. Buy the 6660 for sun and the 6670CT for heat. Wearing both at once means a brim shade and a wet neck shade fighting over the same suspension straps.
  2. Putting a brim shade on a full-brim hat. It doubles the brim and adds bulk for no gain. A full-brim hat needs a neck-only shade.
  3. Wearing an untreated polyester shade near sparks. Only the Radians SE Treated Hi-Vis Neck Shade publishes a flame-resistance standard (ASTM D6413).
  4. Counting on the 4-hour cooling figure in humid weather. Ergodyne’s 4 hours is a best case. Keep a water bottle for re-soaking.
  5. Leaving the shade on through hard hat inspections. Take it off to inspect the shell and suspension, and check the hook-and-loop straps for grit that keeps them from closing.

At about $5-17 apiece, a shade that has lost its elastic or soaked up sweat salt is cheaper to replace than to nurse along. Buying two of the Ergodyne Chill-Its 6660 so one dries while the other is worn costs less than a single cooling vest.

FAQ

Do hard hat sun shades fit full-brim hard hats?

Some state it and some don’t. Radians says the RHHS-01 and the SE Treated Hi-Vis Neck Shade fit full-brim hats, and OccuNomix says the 899 fits most hard hats including full-brim. Ergodyne says the Chill-Its 6660 fits “most hard hats” without claiming full-brim fit, so on a full-brim shell a neck-only shade is the cleaner choice.

What does UPF 50+ mean on a hard hat shade?

UPF 50+ means the fabric lets through no more than 1/50 of UV radiation, so it blocks at least 98%. In the US it is tested under AATCC TM183 and labeled under ASTM D6603. Among the shades listed here, only the Ergodyne Chill-Its 6660 publishes a UPF 50+ rating.

Is a flame-resistant neck shade safe for electrical work?

Flame-resistant is not the same as arc-rated. The Radians SE Treated Hi-Vis Neck Shade meets ASTM D6413, a vertical flame test, but Radians publishes no arc rating in cal/cm², and NFPA 70E arc-flash PPE is chosen by arc rating. Use it for welding and spark exposure. Radians says its self-extinguishing treated polyester is not for use where an arc flash or flash fire hazard exists.

How long does an evaporative cooling neck shade stay cold?

Ergodyne rates both the Chill-Its 6670CT (PVA) and the Chill-Its 6717 (polymer crystals) at up to 4 hours of cooling per soak. The 6717 needs a 2-5 minute soak to activate. Evaporation slows in humid air, so expect less than 4 hours on muggy days, and re-wet the shade to restart the cooling.