Best Impact Resistant Work Gloves
Top pick for rigging, oilfield and demolition: Mechanix SpeedKnit M-Pact S59EP58
Rigging, oilfield and demolition hurt the back of the hand in predictable ways. In rigging, a hand gets caught between a shackle or a swinging load and a beam. On an oilfield drill floor the hazards are tongs, slips and joints of pipe. In demolition it is falling concrete, steel offcuts and a hammer that misses. All three jobs also bring cut and puncture hazards: broken wire rope strands, sheet-metal edges and rebar ends. The gloves below are ranked on four things, in this order:
- A published back-of-hand impact result: an ANSI/ISEA 138 level where the maker or a listing states one, otherwise the P impact mark under EN 388.
- The ANSI/ISEA 105 cut level.
- How well the palm grips wet or oily steel.
- Price.
The one to buy is the Mechanix SpeedKnit M-Pact S59EP58. Grainger lists it at ANSI Cut Level A9, the highest step on the A1 to A9 scale, and ANSI Impact Level 2 under ANSI/ISEA 138. Level 2 means the average force passing through the knuckle and finger guards stayed at or below 6.5 kN in the standard’s 5-joule drop test. The Mechanix spec sheet for the S59EP58 carries the EN 388 code 3X43FP: abrasion 3, tear 4, puncture 3, cut level F on the straight-blade TDM test (the top of the A to F scale), and P for a pass on knuckle impact. No other glove on this list pairs a stated Level 2 impact rating with an A9 cut rating.
Get Mechanix SpeedKnit M-Pact S59EP58This glove suits riggers and demolition crews who handle wire rope, cut steel and broken concrete in the same shift. It also suits roustabouts who want rated knuckle armour in a coated-knit glove rather than a bulky synthetic-leather one. Grainger lists it in sizes S (7) through 2XL (11), and industrial suppliers list it at about $53 to $60 a pair. That price buys the A9 cut rating. On puncture, the published scores do not favour the HexArmor glove below: its EN 388 code 4X21FP gives puncture 1, against 3 in this glove’s 3X43FP, though HexArmor adds an interior SuperFabric layer that it says resists cut, puncture and abrasion.
These picks were not tested. The ranking comes from the makers’ published ratings, retailer listings and the standards those ratings refer to.
How to read impact and cut ratings on the label
ANSI/ISEA 138-2019 is the US standard for the armour on the back of an impact glove. A 2.5 kg striker is dropped onto the knuckles and fingers with 5 joules of energy, and the force that reaches the anvil underneath is measured. The average of those readings sets the level: Level 1 at 9 kN or less, Level 2 at 6.5 kN or less, Level 3 at 4 kN or less. Lower force means better protection, so Level 3 is the best. The level is printed on the glove. Five joules is 2.5 kg dropped about 20 cm. That is far less than a slipping load or a falling joint of pipe, so the rating tells you which glove spreads a blow better. It does not make a pinch point safe to put your hand into.
European gloves show impact differently. Under EN 388:2016 + A1:2018, a P at the end of the six-character code means the knuckle area passed an impact test based on EN 13594: an average transmitted force of 7 kN or less, with no single reading above 9 kN. It is a pass or fail, not a grade. A glove with a P and no ANSI 138 level has not been graded on the ANSI scale, but that does not mean it would score worse. The Mechanix M-Pact MPT-58 is sold on its P mark without a published ANSI 138 level. HexArmor, Ironclad and Ansell state ANSI/ISEA 138 Level 2 for the Chrome Series 4026, the KONG Original and the Ringers R065.
Cut resistance in the US is ANSI/ISEA 105, scored by how many grams of blade load it takes to cut through the material on a TDM-100 machine. A1 starts at 200 g, A4 at 1,500 g, A8 at 5,000 g and A9 at 6,000 g. The HexArmor Chrome Series 4026, for example, is listed at 5,486 g, which puts it in A8. For rigging with wire rope and for demolition among sheet metal and rebar, a cut level of A4 or above is a sensible minimum. On a drill floor where the main hazard is crushing rather than slicing, a lower cut level such as A2 can be the right trade for a thicker, grippier palm.
Get HexArmor Chrome Series 4026Grip is the third deciding point, and the makers describe it differently: a sandy nitrile finish, a dotted double-layer synthetic palm, or HexArmor’s Mud Grip coating. HexArmor names dry or light oil for Mud Grip. Mechanix says the S59EP58’s sandy nitrile palm grips in oily and wet conditions, and Ansell says the R065’s sandy palm grips in wet and dry environments.
The rest, ranked, and who should buy each instead
2. HexArmor Chrome Series 4026: for wire rope rigging and sharp demolition debris. The HexArmor Chrome Series 4026 puts a layer of SuperFabric material inside the palm. HexArmor says it gives cut, puncture and abrasion resistance, and listings rate the glove ANSI cut A8 with ANSI puncture level 2. The outer palm is HexArmor’s Mud Grip synthetic leather with PVC dots, which the maker describes for dry or light oil. High-visibility impact guards cover the back of the hand, and the EN 388 code is 4X21FP, so the guards pass the P impact test. HexArmor’s own store lists it at about $59 to $65 a pair in sizes XS through 3XL. Buy it over the top pick when abrasion is the main wear, from frayed wire rope, nail-studded lumber or torn metal: HexArmor rates it ANSI abrasion 6 against the top pick’s 4, though its EN 388 puncture score of 1 is lower than the top pick’s 3. Don’t buy it for fine fastener work, because the layered palm is thicker than a knit. HexArmor also states its gloves are cut and puncture resistant, not cut and puncture proof, and must not be used with moving or serrated blades or tools.
3. Ironclad KONG Original: for drill-floor and well-site crews. Ironclad developed the Ironclad KONG Original (SDX2) with the oil and gas industry’s safety committee, whose members included ExxonMobil, ConocoPhillips, Chevron and Halliburton. Ironclad’s TPR armour runs over the fingers, thumb, knuckles and the metacarpal, the long bones on the back of the hand that a joint of pipe can land on. The palm is a double-layer dotted synthetic, and the cuff is slip-on neoprene. The EN 388 code is 4242AP: abrasion 4, cut 2 on the coup test, tear 4, puncture 2, TDM cut A, and the P impact pass. Listings give ANSI cut A2. Ironclad lists it at $34.99 in sizes S through 3XL. Buy it over the top pick when crushing on a drill floor is the hazard and you want the most armour coverage per dollar. Don’t buy it for sheet-metal or rebar demolition: A2 is a low cut rating.
Get Ironclad KONG Original4. Ringers R065: for dexterity and a lower price. The Ringers R065, now sold under Ansell, is a 13-gauge HPPE knit with a sandy nitrile half-dip palm, a knitwrist cuff and TPR guards on the back. Ansell’s spec sheet gives EN 388 4X43EP: TDM cut level E plus the P impact pass. Ansell lists it in sizes 7 to 13 and names oilfield tasks for it, including running tools into the wellbore, pipe handling, and make-up and break-out tools. Bayshore Safety lists a pair at $28.00. Buy it over the top pick for wellhead and maintenance work that means threading bolts, pins and hose fittings. Don’t buy it for soaking-wet or heavily oiled work: a half-dip leaves the knit back uncoated, so fluid can soak through from the back of the hand.
Get Ringers R0655. Mechanix M-Pact MPT-58: for low-cut, general impact work. The Mechanix M-Pact MPT-58 has a synthetic leather palm, a hook-and-loop closure and TPR knuckle and finger guards that Mechanix says meet EN 388 impact standards. Its EN 388 code is 2121XP, and Mechanix states no ANSI/ISEA cut or puncture level for it. Mechanix lists M-Pact colorways at under $30. Buy it for equipment maintenance, loading or tool-room work where knuckle knocks are the only real hazard. Don’t buy it for demolition or for handling cut steel: its EN 388 coup cut score is 1, the lowest pass on that scale.
Get Mechanix M-Pact MPT-58Oilfield specifics: grip in oil, cuffs and FR
On a well site, the cuff matters nearly as much as the armour. The Ironclad KONG Original’s slip-on neoprene cuff has no strap to snag on a tong handle, and it closes the gap where mud and drilling fluid get in at the wrist. The knitwrist on the Ringers R065 does the same job more loosely and is easier to pull off with a wet hand. The Mechanix M-Pact MPT-58 has an extended hook-and-loop wrist closure, which Mechanix says gives a secure fit.
Grip in oil is where coatings differ. HexArmor states its Mud Grip palm is for dry and light oil conditions, so on the HexArmor Chrome Series 4026 heavy, standing oil is outside what the maker claims. Ansell says the Ringers R065’s sandy nitrile palm grips in wet and dry environments; it makes no claim for oil. The KONG Original’s dotted double-layer palm relies on its raised dots and the extra thickness of the second layer.
High visibility helps on a drill floor, where a hand in the wrong place needs to be seen. The HexArmor 4026 has high-visibility guards on the back, and the KONG Original has a hi-viz palm. Many operators also require flame-resistant clothing. None of the five gloves here is sold as a flame-resistant glove. If your site’s hazard assessment calls for FR hand protection, choose a glove its maker rates as flame resistant, and see the best FR clothing for oil and gas workers for the rest of the kit.
What is not worth the money
Rubber on the back of a glove is not the same as rated impact protection. A glove sold as an impact glove that shows neither an ANSI/ISEA 138 level nor a P in its EN 388 code has no published impact result at all. At any price, it should lose to the $28 Ringers R065, which carries the P mark.
An A9 cut rating is not worth paying extra for when nothing on the job cuts. On a drill floor handling pipe and tongs, the Ironclad KONG Original’s A2 rating with full metacarpal armour fits the hazard better than a high-cut knit at a higher price. The reverse also holds: a demolition crew cutting out ductwork gets little from extra armour if the glove has no ANSI cut rating, like the Mechanix M-Pact MPT-58.
Paying more to move from Level 1 to Level 3 makes sense only if the blows you take are the kind the test measures. The ANSI 138 test drops 5 joules, equal to 2.5 kg falling about 20 cm. That matches a dropped tool, a swinging hook or a pipe end that grazes the knuckles. It does not match a hand pinned between a suspended load and a column. No glove in any catalogue is rated for that, which is why rigging practice uses tag lines and keeps hands away from pinch points. The glove covers the near-misses.
Sizing, fit and when to replace a pair
An impact glove only works if the guards sit over the joints they are meant to cover. If the glove is too big, the knuckle pad rides up past the knuckle, and the 5-joule test result no longer describes what protects your hand. The size ranges differ more than you might expect. Grainger lists the Mechanix SpeedKnit M-Pact S59EP58 from S (7) to 2XL (11). Ansell sizes the Ringers R065 from 7 to 13. HexArmor sells the Chrome Series 4026 from XS to 3XL. Ironclad’s part numbers for the KONG Original run from SDX2-02-S to SDX2-07-XXXL. Workers with the largest hands get the most room in the Ringers range, which runs to size 13; the HexArmor 4026 and the KONG Original stop at 3XL.
Replace a pair once the protection has failed, not when it starts to look worn. The point to replace is when a TPR guard splits or tears away from the shell, when the palm coating wears through to the knit or liner, or when a cut has gone all the way through the palm. A cut-through glove no longer meets its A-level at that spot, and a guard that has separated no longer spreads impact the way it did in the test. Wire rope wears out palms fastest. That is where the HexArmor 4026’s interior SuperFabric layer earns its higher price over a knit.
For framing, finish carpentry or general site work where crushing is a smaller part of the job, the best work gloves for construction list covers lighter gloves that give up some armour for feel.
Related guides
- 21° vs 30° Framing Nailers: Match the Angle, Collation and Nails
- Best ATV/UTV Tool Boxes and Cargo Racks (2026): For Farm and Ranch Work
- Best Balaclavas and Neck Gaiters for Cold Work
- Best Bib Overalls for Construction and Cold-Weather Work (2026)
FAQ
Is ANSI/ISEA 138 Level 1 enough for rigging?
Level 1 means the average transmitted force stayed at or below 9 kN in the 5-joule test. Level 2 lowers that limit to 6.5 kN and Level 3 to 4 kN. For riggers who handle shackles and hooks all shift, a Level 2 glove such as the Mechanix SpeedKnit M-Pact S59EP58 lets less force through the guards. No level makes it safe to put a hand between a load and a fixed object.
Do impact gloves also need cut resistance?
For rigging and demolition, yes, because wire rope strands, sheet metal and rebar cut as often as loads crush. A cut level of A4 or above is a sensible minimum there. The top pick is listed at A9 and the HexArmor Chrome Series 4026 at A8. On a drill floor where crushing dominates, a lower cut level such as the A2 Ironclad KONG Original can be the better trade.
What does an EN 388 code like 4X43EP mean?
The six characters are abrasion (4), coup cut (X, not tested), tear (4), puncture (3), TDM cut (E on an A to F scale) and impact (P for a pass). That is the code Ansell gives for the Ringers R065. The P shows the knuckle area passed a test allowing an average of 7 kN or less, with no single reading over 9 kN.