Best Portable Jobsite Heaters
Top pick for enclosed work areas: Mr. Heater Big Buddy MH18B
For a ventilated job trailer, truck cap or similar small enclosure where people are working, buy the Mr. Heater Big Buddy MH18B. Mr. Heater rates it safe for indoor use in small recreational enclosures having means for providing combustion air and ventilation, such as cabins, trailers, truck caps and vans, and for emergency indoor heating on a 1 lb cylinder. Mr. Heater rates it at 4,000, 9,000 and 18,000 BTU per hour and lists coverage up to 450 square feet. The maker sells it as indoor safe, with a low-oxygen shutoff and a tip-over shutoff. On its two on-board 1 lb cylinders, Mr. Heater claims up to 11 hours. Its owner’s manual gives a rough guideline of 48 to 216 hours on two 20 lb cylinders connected by the optional hoses.
Get Mr. Heater Big Buddy MH18BThese picks were not tested. The ranking comes from the makers’ specifications, owner’s manuals and retail listings. The criteria, in order: whether the maker allows indoor use; which automatic shutoffs it has (oxygen depletion sensor, tip-over switch, flame-out sensor); BTU output for the size of the space; runtime per tank; what else it needs (a 120V outlet or a tool battery); and price. The Big Buddy is the only heater here that does all of these well. It has indoor approval, both shutoffs, three output steps, two fuel options and no cord.
It has limits. Mr. Heater says never to leave it unattended while burning, and allows a remote refillable cylinder (20 lb maximum) only when the cylinder is located outdoors. The Big Buddy owner’s manual requires a vent area of 18 square inches at the ceiling and at floor level while it runs (the example given is a 4 1/4 x 4 1/4 inch opening) and says not to run other fuel-burning appliances in the same space. If you need to heat a 1,500 square foot open slab or an uninsulated framed shell, don’t buy it: 18,000 BTU won’t hold a working temperature there, and a forced-air heater below is the right buy. Mr. Heater restricts the Buddy heaters from all indoor use in Massachusetts and Canada. Mr. Heater sells a separate MH18B for those markets and lists it as an outdoor heater.
Mr. Heater’s own store lists the Big Buddy at about $240. Mr. Heater’s warranty policy gives a 1-year limited warranty.
Smaller and cordless radiant heaters: Portable Buddy and DeWalt DXH12B
The Mr. Heater Portable Buddy MH9BX is the budget pick for one person in a small space, like a pump house, a parked trailer or a single room under 225 square feet. Mr. Heater rates it at 4,000 or 9,000 BTU per hour and up to 225 square feet. It has the same low-oxygen and tip-over shutoffs as the Big Buddy. Its manual requires a minimum vent area of 9 square inches at the ceiling and at floor level, allows use in a recreational enclosure only with a window or roof vent, and says never to leave it unattended, run it while sleeping or operate it in a moving vehicle; Mr. Heater restricts it from all indoor use in Massachusetts and Canada. On one 1 lb cylinder, Mr. Heater lists about 3 hours on high and 6 hours on low. Retail listings put it around $80-90 (North 40 lists $89.99), and Mr. Heater’s own store lists it higher. Buy it if you need heat for part of a shift in a small room. Don’t buy it to heat a crew. Half the Big Buddy’s top output and one cylinder at a time mean you’ll be swapping cylinders through the day.
Get Mr. Heater Portable Buddy MH9BXThe DeWalt DXH12B suits a crew already on DeWalt 20V MAX or FLEXVOLT batteries. DeWalt no longer lists the DXH12B: its product page now redirects to DeWalt’s home page. DeWalt rates it at 6,000 and 12,000 BTU per hour and lists it as CSA certified indoor safe (outdoor use only in Massachusetts and Canada). The battery powers the fan and electronic ignition, an LED work light and USB charging ports. The heat comes from propane; DeWalt lists dual tank capability. Retail listings run about $190-210 (Tractor Supply $189.99, Contractors Direct $208.95).
Get DeWalt DXH12BCompared with the Big Buddy, the DXH12B has 6,000 BTU less at the top setting, has no 4,000 BTU low, and costs less than the Big Buddy’s $240 price on Mr. Heater’s store. What it adds is the battery platform, the light and the USB ports, not heat. Buy it only if those extras matter to you. Otherwise the Big Buddy gives more heat for the money.
Forced-air heaters for open shells and large bays: Dyna-Glo and Milwaukee
For a framed shell, warehouse bay or pole barn with ventilation, buy the Dyna-Glo RMC-FA60DGD. Dyna-Glo rates it at 30,000 to 60,000 BTU per hour, continuously variable, and lists coverage up to 1,350 square feet. It uses continuous electronic ignition and comes with Dyna-Glo’s Easy-Connect regulator and hose for a propane tank. The owner’s manual says it is not for home or recreational vehicle use. It’s a construction heater for ventilated spaces, not an occupied room. Dyna-Glo’s manual says never to leave it unattended while burning, to keep combustibles at least 24 in. from the sides, 36 in. from the top and 72 in. from the front, not to use it on finished floors, to keep it at least 6 ft from any propane container and not aim it at one within 20 ft, never to use it where gasoline, solvents, paint thinners or dust may be present, and not to use it in garages in Canada. Amazon listings show it from about $160-180. It needs a 120V outlet for the fan and ignition, so don’t buy it for a site without power.
Get Dyna-Glo RMC-FA60DGDThe Milwaukee M18 70,000 BTU Forced Air Propane Heater (0801-20) is the pick for a site without power. Milwaukee no longer lists the 0801-20: its product page now redirects to a different product. Milwaukee’s manual lists 18V DC from an M18 battery or 120V AC, with a draw of 1.7 A on the battery and 0.25 A on AC. It rates the operating range at 0°F to 80°F, and output varies from 30,000 to 70,000 BTU per hour. It comes with a 10-foot hose and regulator. Milwaukee’s product page says not to use it in a confined space or for home or recreational vehicle use, and to use it only in a properly ventilated area. Its manual requires clearances from combustibles of 7 ft at the front, 4 ft at the sides and 6 ft at the top, says to keep it at least 10 ft from propane containers and not aim it at them within 20 ft, not to operate it above 2,000 ft altitude or while sleeping, not to use it to heat human living quarters, and to monitor CO, CO2 and NO2 at the start of each shift and after 4 hours. The tool warranty is 1 year. Buy it only if being cordless matters. If you have an outlet, the Dyna-Glo RMC-FA60DGD does the same job for less. Milwaukee no longer lists the 0801-20 on its site (its product page now redirects to a different product), so check that the listing you buy from has it in stock.
Get Milwaukee M18 70,000 BTU Forced Air Propane HeaterFor big spaces on kerosene, buy the Dyna-Glo KFA80DGD. GHP Group, which makes Dyna-Glo heaters, no longer lists the KFA80DGD in its store: its product page now redirects to the store’s home page. Dyna-Glo rates it at 80,000 BTU per hour and up to 1,900 square feet. It has a thermostat, a flame-out sensor and a fuel gauge that shows remaining run time. Dyna-Glo lists 1 K kerosene, #1 diesel and #1 fuel oil as its fuels, and its manual gives a 5.0-gallon tank and fuel consumption of 0.60 gallons per hour. Like the Dyna-Glo RMC-FA60DGD, it needs 120V power (the manual specifies a 125V, 8 A fuse). Listings show $199.99 at Northern Tool. Kerosene smells more than propane and is harder to fill on site. Dyna-Glo’s manual says to use it only in well-ventilated areas, with at least 3 sq ft of fresh-air opening for each 100,000 BTU/hr, and never in living or sleeping areas. It also says to keep 8 ft clear at the outlet and 4 ft at the sides, top and rear, never to leave it unattended while burning, never to refill it while it is operating or still hot, and never to transport it with fuel in the tank. Massachusetts law prohibits its use in any building used in whole or in part for human habitation. Buy the KFA80DGD if your site already keeps diesel or kerosene and you’d rather not handle propane cylinders.
Get Dyna-Glo KFA80DGDElectric option: DeWalt DXH165 and the limits of a 120V outlet
The DeWalt DXH165 is a 1.65 kW forced-air electric construction heater on 120V with a thermostat. DeWalt no longer lists the DXH165: its product page now redirects to DeWalt’s home page. DeWalt’s manual lists its output as 5,630 BTU per hour (1,650 W). It doesn’t burn anything, so it adds no carbon monoxide and no water vapor. DeWalt’s manual says it is for indoor use only and must not be exposed to wet conditions, to keep combustibles at least 6 feet from the front and 2 feet from the sides and rear, and to use extreme caution whenever it is left operating and unattended. That makes it fit for a finished interior, an occupied office trailer or a room where drywall mud is drying. DeWalt warns that it has internal electrical components that spark during use and must not be used in areas where fumes from gasoline, paint or other flammable liquids may be present.
Get DeWalt DXH165The catch is output: 1 watt is 3.412 BTU per hour, so even 1,650 W is under a third of the Big Buddy’s 18,000 BTU high setting. DeWalt’s manual lists the DXH165’s electrical supply as 115V, 13.5 A. A heater running for hours counts as a continuous load, and 13.5 A is more than 80% of a 15 A circuit. Put it on a 20 A circuit, not a shared 15 A temporary outlet that’s also running saws. Ohio Power Tool’s listing shows about $290.
The verdict: buy electric only when combustion isn’t allowed or moisture would ruin the work. In every other jobsite case, propane gives more heat for the money, and no portable plug-in heater will warm an open shell.
Matching BTU output and tank size to the job
Start with the maker’s square-foot rating, then do the fuel math. A pound of propane holds about 21,600 BTU, so a full 20 lb cylinder holds about 432,000 BTU. That gives roughly:
- Mr. Heater Big Buddy MH18B on high (18,000 BTU): about 24 hours per 20 lb cylinder.
- Dyna-Glo RMC-FA60DGD at 60,000 BTU: about 7 hours per 20 lb cylinder; about 14 hours at its 30,000 BTU low.
- Milwaukee 0801-20 at 70,000 BTU: about 6 hours per 20 lb cylinder.
- 1 lb cylinder on a 9,000 BTU heater: about 2.4 hours, close to the 3 hours Mr. Heater lists for the Portable Buddy on high.
Kerosene holds about 135,000 BTU per gallon, so the KFA80DGD’s 5-gallon tank holds about 675,000 BTU. At 80,000 BTU per hour that’s about 8.4 hours, consistent with the 0.60 gallons per hour fuel consumption and 5.0-gallon tank Dyna-Glo’s manual lists.
Cold weather also limits large propane heaters, and the problem is the tank, not the heater. Flame Engineering’s propane vaporization chart shows a full 100 lb cylinder supplying 113,000 BTU per hour continuously at 0°F, 167,000 at 20°F and 214,000 at 40°F. Smaller and emptier cylinders supply less. Dyna-Glo’s chart for its 40,000-60,000 BTU/h heaters lists one 20 lb tank down to 10°F, two 20 lb tanks at -10°F and one 100 lb tank at -20°F, and notes that less gas is vaporized at lower temperatures. Milwaukee’s manual lists a propane tank icing over as a cause of gradual heat reduction. Milwaukee’s manual specifies a propane cylinder of 20 lb maximum capacity (12 in. diameter x 18 in. tall) for the 0801-20. Mr. Heater’s Buddy manuals say runtimes can be significantly reduced when operating continuously at temperatures below 20°F and recommend a 20 lb tank in those conditions.
Indoor-safe ratings, ventilation and moisture
“Indoor safe” on a propane heater is a specific approval from the maker for that model, not a general rule. The Big Buddy, the Portable Buddy and the DeWalt DXH12B carry it. Each has an oxygen depletion sensor that shuts off the gas when oxygen in the room drops, plus a tip-over switch. The Dyna-Glo RMC-FA60DGD and Milwaukee 0801-20 are construction heaters, and both makers rule out home and recreational vehicle use; Milwaukee also says not to use the 0801-20 inside a confined space. The Dyna-Glo KFA80DGD relies on a flame-out sensor and its manual’s ventilation rules, not an oxygen depletion sensor. Forced-air heaters vent all of their combustion gases into the room, so they belong in large, ventilated spaces.
Even indoor-rated heaters need fresh air. The Big Buddy manual requires 18 square inches of vent area and allows use in a recreational enclosure only if it has a window or roof vent. For a work-truck cap, enclosed trailer or ice-house-style shelter, that’s the rule to follow. None of these heaters is approved for use while sleeping or in a moving vehicle. Bring a battery CO alarm for any enclosed space.
Moisture is the trade-off people don’t plan for. Burning propane gives off about 1.6 lb of water for every pound of fuel: one 20 lb cylinder releases roughly 33 lb, or about 4 gallons, of water into the air. In a tight space that means condensation on cold glass and steel, drywall mud that’s slower to cure, and finishes that blush. If the work is moisture-sensitive, use electric heat or ventilate hard.
What’s not worth the money, and how heaters fail on site
Not worth the money:
- A cordless 70,000 BTU heater on a site with power. The Milwaukee 0801-20 burns propane; its M18 battery or 120V AC cord powers the fan and ignitor. The Dyna-Glo RMC-FA60DGD gives similar heat from an outlet for much less.
- A small radiant heater for a whole floor. A 9,000 BTU Portable Buddy rated for 225 square feet won’t hold temperature in a 1,000 square foot open shell, however long it runs.
- Full-shift heat from 1 lb cylinders. At about 2-3 hours per cylinder on high, cylinder cost adds up fast. Buy the hose and run a 20 lb tank instead.
- A plug-in electric heater for open framing. 1,650 W is about 5,630 BTU, under two-thirds of a Portable Buddy on high (9,000 BTU).
Common failures:
- Oily residue from a bulk tank. Mr. Heater’s manual requires its F273699 fuel filter, replaced annually, with hoses F273701, F273702 or F272702 (its F273704 Buddy series hose needs no filter), and the Big Buddy manual’s troubleshooting table lists cleaning or replacing the pilot assembly when the pilot won’t stay lit.
- Tip switch faults. The same manual lists disconnected tip-switch wires as a cause of the pilot not staying lit, and a tip-over switch activated by bumping the heater as a cause of it shutting off during normal operation.
- Starved tanks. Frost on a 20 lb cylinder feeding a forced-air heater means the tank can’t vaporize propane fast enough. Dyna-Glo’s chart calls for more or larger tanks as temperatures drop; Milwaukee limits the 0801-20 to a 20 lb cylinder and, when the tank ices over, says to wait 15 minutes before relighting.
- Tripped breakers. A 1,650 W electric heater sharing a 15 A temporary circuit with tools.
A heater warms the room, not someone working outside on the scaffold or at the gate. For layers, gloves and heated gear for those crews, see the cold-weather workwear guide.
Related guides
- 21° vs 30° Framing Nailers: Match the Angle, Collation and Nails
- Best ATV/UTV Tool Boxes and Cargo Racks (2026): For Farm and Ranch Work
- Best Balaclavas and Neck Gaiters for Cold Work
- Best Bib Overalls for Construction and Cold-Weather Work (2026)
FAQ
Can I run a Mr. Heater Big Buddy inside a work trailer or truck cap?
Mr. Heater rates the Big Buddy MH18B as indoor safe. Its manual allows use in a recreational enclosure only if there’s a window or roof vent, and requires a vent area of 18 square inches at the ceiling and at floor level while it runs. Don’t run it while sleeping, while the vehicle is moving or unattended, and keep a CO alarm in the space.
How long does a 20 lb propane tank last on a jobsite heater?
A 20 lb tank holds about 432,000 BTU. That’s about 24 hours on a Big Buddy at 18,000 BTU, about 7 hours on a Dyna-Glo RMC-FA60DGD at 60,000 BTU, and about 6 hours on the Milwaukee 0801-20 at 70,000 BTU. Dyna-Glo’s chart for its 40,000-60,000 BTU/h heaters lists one 20 lb tank down to 10°F, two 20 lb tanks at -10°F and one 100 lb tank at -20°F; Milwaukee’s manual specifies a propane cylinder of 20 lb maximum capacity for the 0801-20.
Is a forced-air propane heater safe in an enclosed garage or room?
Not unless the maker allows it and the space is ventilated. Dyna-Glo says the RMC-FA60DGD is not for home or RV use, and Milwaukee says not to use the 0801-20 in a confined space and to keep it at least 10 feet from propane containers and 7 feet from combustibles at the front. For an enclosed, occupied room, use an indoor-rated radiant heater with an oxygen depletion sensor, such as the Big Buddy.