Best Safety Helmets for Work at Height

The best helmet for work at height and rigging

For work at height and rigging, buy the Milwaukee BOLT 48-73-1300 safety helmet. Milwaukee rates it ANSI/ISEA Z89.1 Type II, Class C, so it is tested for impacts to the front, back and sides as well as the top. Its five-buckle chin strap meets the strength and effectiveness clauses of EN 12492:2012, the climbing helmet standard. It fits hat sizes 6-1/2 to 8-1/2 and has four BOLT accessory slots plus two universal slots.

Get Milwaukee BOLT 48-73-1300 safety helmet

Work at height and rigging asks four things of a helmet that a ground-level hard hat does not have to do. First, a fall into the arrest or a swing into a column hits the head from the side. ANSI Type II testing covers side impacts; Type I covers only the top. Second, the helmet has to stay on through that fall, so the chin strap has to hold. Petzl, for example, sets its high-strength chinstrap setting to a strength greater than 50 kg, to reduce the risk of the helmet coming off in a fall. Third, when you look up at a load, an anchor or a sheave, a full brim catches on lanyards and blocks your view, so a low-profile shell works better. Fourth, conditions vary: a steel deck or tower in summer calls for vents, while work near energized conductors needs a non-vented Class E shell tested to 20,000 volts.

None of these helmets were tested for this page. The ranking comes from each maker’s published certifications and specifications, and every figure below is the maker’s own.

The ranking, with who each one suits:

Milwaukee BOLT 48-73-1300: why it is the top pick

The Milwaukee BOLT 48-73-1300 safety helmet combines the two things that matter most at height: Type II impact protection and a chin strap built to a climbing standard. Klein lists the same EN 12492:2012 retention clauses for its Type-2 Class E helmet. Milwaukee’s specification sheet lists it as ANSI/ISEA Z89.1 Type II Class C. The same sheet says the retention system meets clause 4.2.3 (strength) and clause 4.2.4 (effectiveness) of EN 12492:2012. That is the pairing a rigger needs: Type II covers the side strike, and the chin strap rating keeps the helmet on when a cap-style hard hat would come off. Milwaukee still calls the protection limited: its instructions say the helmet does not protect against larger objects, severe impact, penetration, or objects traveling at accelerated speeds, must not be used if it does not fit snugly, and must be disposed of immediately after any impact, even if damage is not visible. Milwaukee recommends replacing it after 5 years of service, says to retire it after 5 years of service or 10 years from the date of manufacture, says not to use it near an open flame, and says not to store it in direct sunlight or in heat over 120°F (49°C). Milwaukee tests these helmets to withstand temperatures from -22°F to 122°F.

The shell is LEXAN polycarbonate. Inside is a padded suspension with a swinging ratchet. Milwaukee’s hat size range of 6-1/2 to 8-1/2 is the widest on this list. The MSA and Petzl helmets cover 53 to 63 cm, roughly hat sizes 6-5/8 to 7-7/8, and Klein stops at 8. If you wear a size 8 or larger, this is the helmet on this list that fits with room to spare.

It comes with a BOLT headlamp mount that takes most strap headlamps and a BOLT marker clip. Milwaukee says the four BOLT slots and two universal slots integrate additional personal protection equipment and accessories, and its instructions say to use only Milwaukee helmet accessories with Milwaukee helmets. The sweatband and liner are antimicrobial and moisture-wicking. The sweatband, liner and chin strap are all machine washable, which matters on a helmet worn through a summer of sweat.

Who should not buy it: anyone working near energized lines or equipment. Class C means the vented shell has no electrical rating. Milwaukee’s specification sheet also lists Type II Class E non-vented versions of the BOLT helmet. Electricians who want the BOLT accessory system should buy one of those. If you hang on rope all day and want the lightest helmet you can get, the Petzl pair below suits you better.

MSA V-Gard H2: the runner-up, with a Mips option

The MSA V-Gard H2 safety helmet is the runner-up. Choose it if your crew already uses MSA V-Gard accessories or your site requires protection against rotational impact. MSA certifies it to ANSI Z89.1 Type II. It comes vented, rated Class C, or non-vented, rated Class E, so one model can cover both the steel crew and the electricians. MSA lists the vented orange version at 0.490 kg (1.080 lb), with an ABS shell, a 53 to 63 cm head range and a low-profile climbing shape with no full brim.

Get MSA V-Gard H2 safety helmet

The chinstrap is integrated into the helmet; MSA pairs it with the Type II certification for enhanced protection against lateral impacts. MSA also offers the H2 with an optional Mips system for added protection against rotational impacts; MSA says it helps reduce the risk of brain trauma by redirecting rotational energies in the event of certain angled impacts.

It ranks below the Milwaukee on fit range and on what comes in the box. The Milwaukee’s sizing runs past the H2’s 63 cm, and it comes with a BOLT headlamp mount. Buy the H2 instead when a mixed crew needs the same helmet in both Class C and Class E, or when your site requires Mips. Do not buy the vented H2 for electrical work; only the non-vented shell carries the Class E rating, and MSA says Class C helmets do not supply electrical protection. MSA says a Class E helmet supplies limited protection from electrical shock: do not use it alone, use other insulating protective equipment for the risk, and make sure the nominal voltage is not more than the helmet’s electrical limits. MSA also says the helmet provides limited protection, must not be used to go into areas where there is a risk of severe impact or penetration from dangerous objects, and must always be replaced after impact or penetration, even if damage is not readily apparent. It has a service life of 5 years in addition to storage time of up to 2 years; store it out of direct sunlight and not over 120°F (49°C), and use only MSA V-Gard accessories.

Klein Tools Type-2 Class E: for electrical work at height

The Klein Tools Type-2 Class E safety helmet is the pick for electricians, linemen and tower crews who climb near energized equipment. Klein’s instructions still warn to avoid areas where the chance of electrical shock exists, because the non-vented version provides limited electrical protection. They also say to dispose of the helmet immediately after any impact, even if damage is not visible, to replace the suspension and chin strap after no more than 12 months of use, and to replace the helmet after 2 years of use or 5 years from manufacture, whichever comes first. Exposure to direct sunlight, corrosive environments, and/or temperatures below -40°F (-40°C) or above 120°F (49°C) can lessen its ability to withstand impact and penetration. Klein says the helmet provides LIMITED protection from small objects striking its top, front, back and sides, and not to expose the helmet, EPS insert, suspension, padding or chin strap to open flame. Klein rates it to ANSI Z89.1-2014 (R2019) Type II Class E, tested for top, front, back and side impact and for electrical protection up to 20 kV. Klein says it designed the non-vented shell with electricians and linemen in mind and made it compact for at-height and confined-space work. The shell is a PC/ABS composite, and the short, low-profile bill keeps the view clear when you look up a pole or ladder.

Get Klein Tools Type-2 Class E safety helmet

A 6-point suspension and a large-knob ratchet handle the fit; Klein says the ratchet adjusts one-handed with gloves on. A detachable 4-point padded chin strap holds the helmet steady when you tilt your head to look up or down from a bucket or a rung. The hat size range is 6-1/2 to 8. Klein’s patented mounts on the front and back take its own headlamps without straps or zip ties. That is useful in vaults, attics and night outages, where a strap-on lamp tends to slide.

The padded sweatband and top pad wick sweat and are machine washable. The shell has no vents, which is the trade-off for the Class E rating. Klein also sells a vented Class C version of its Type-2 helmet. But if you do not need the electrical rating, the Milwaukee’s wider sizing and six accessory slots make it the better buy for the money.

Petzl Vertex Vent: for rope access and rescue crews

The Petzl Vertex Vent helmet is for rope access technicians, tower rescue teams and riggers who switch between hanging on rope and working on the ground in the same shift. Petzl certifies it to EN 397 (industrial helmets), EN 12492 (climbing helmets) and ANSI Z89.1 Type I Class C. Its DUAL chinstrap clip has two settings. High strength, which Petzl sets above 50 kg, reduces the risk of the helmet coming off in a fall. Low strength releases below 25 kg, to reduce the risk of strangulation if the helmet becomes snagged while you work on the ground.

Get Petzl Vertex Vent helmet

Petzl lists the weight as 490 g and the head range as 53 to 63 cm. A six-point textile suspension holds the helmet centred while you hang in a harness and look up. So do the CENTERFIT wheels on each side and the FLIP&FIT headband, which sits low on the back of the head. Sliding shutters open or close the vents while you wear it. Petzl certifies it to EN 12492 only with the shutters open and the chinstrap set above 50 kg, and to EN 397 only with the shutters closed and the chinstrap set below 25 kg. Petzl tested it for use between -30° C and +50° C and says to retire it after a major impact, because a major impact can reduce its protection without leaving visible signs of damage. Petzl gives it a 10-year lifespan, says not to use it if you are unable to adjust it to fit properly, and says not to expose it to high temperatures, for example inside a vehicle in direct sunlight. Front and rear slots take Petzl headlamps, and clips hold a headlamp with an elastic headband.

It ranks below the three Type II helmets for one reason: under ANSI it is Type I, tested for top impact only. EN 12492 does include impacts to the front, sides and rear of the shell, which is part of why rope access crews use it. But if your site rules call for ANSI Type II, this helmet does not meet them. It is also Class C, so it is not for electrical work.

Petzl Strato Vent: the lightest on this list

The Petzl Strato Vent helmet is the lightest on this list whose maker states a weight: Petzl lists it at 415 g, against 490 g for the Vertex Vent and the vented MSA V-Gard H2 and 567 g for the Klein Tools Type-2; Milwaukee’s spec sheet gives no weight for the BOLT. Petzl certifies it to EN 12492 and ANSI Z89.1 Type I Class C. It has the same two-setting chinstrap clip as the Vertex: high strength for work at height, low strength for work on the ground. Petzl states it meets EN 12492 only with the chinstrap set above 50 kg; the ground setting, below 25 kg, reduces the risk of strangulation if the helmet becomes snagged. Petzl tested it for use between -30° C and +50° C and says to retire it after a major impact, because a major impact can reduce its protection without leaving visible signs of damage. Petzl gives it a 10-year lifespan, says not to use it if you are unable to adjust it to fit properly, and says not to expose it to high temperatures, for example inside a vehicle in direct sunlight. The head range is 53 to 63 cm.

Get Petzl Strato Vent helmet

The shell is ABS with EPP and EPS foam inside, and the comfort foam is changeable. CENTERFIT wheels keep it centred, and the FLIP&FIT headband folds into the shell, for easy storage and transportation; Petzl says not to compress the helmet. The vent holes let air flow through all day, though unlike the Vertex Vent, Petzl lists no sliding shutters for them.

Buy it for long days on rope, arborist climbs or rescue work, where weight on your neck counts for more than a Type II rating. Do not buy it for steel erection or for work under suspended loads, where the main hazard is a side strike from a swinging beam. A Type II helmet such as the Milwaukee BOLT or the MSA V-Gard H2 suits that job. Like the Vertex Vent, it is Class C, so keep it away from energized equipment.

Type, class and chin strap: what decides the purchase

ANSI/ISEA Z89.1 rates every industrial helmet on two separate scales. Type covers impact: Type I is tested for blows to the top of the head only. Type II adds impacts to the front, back and sides, an off-center penetration test and chin strap retention requirements. Class covers electricity: Class G is tested at 2,200 volts, Class E at 20,000 volts, and Class C has no electrical rating. A vented shell is always Class C, because the vent holes give current a path through the shell.

The two scales are independent, so check both on the label. The Petzl helmets are Type I Class C: strong retention and a climbing certification, but no side-impact rating under ANSI and no electrical rating. The Klein Type-2 is Type II Class E. The Milwaukee BOLT 48-73-1300 is Type II Class C. The MSA V-Gard H2 is Type II in either class, depending on whether you choose the vented or non-vented shell.

Not worth the money: a chin strap clipped onto a Type I cap-style hard hat to make it do for work at height. Type II testing judges the shell, suspension and chin strap retention together, so an add-on strap does not turn a Type I hat into a Type II helmet. For ground-level work, where a brim keeps off sun and rain, a cap or full-brim hard hat is still the right buy, and the hard hat picks cover those.

A helmet protects only your head. Stopping the fall itself takes a full-body harness built to ANSI Z359.11 and a connector rated for the anchor. The roofer harness picks cover the attachment points, sizing and lanyard choices that decide that purchase.

FAQ

Is a Type II helmet required for work at height?

Federal OSHA construction rules require head protection that meets ANSI Z89.1, but they do not name Type II by themselves. Employers and site owners can and do write Type II into their own rules for work aloft. If your site requires it, the Milwaukee BOLT, MSA V-Gard H2 and Klein Tools Type-2 helmets meet it, and the Petzl Vertex Vent and Strato Vent do not.

Can I wear a rock climbing helmet on a job site instead?

Only if it also carries ANSI Z89.1 certification. A recreational climbing helmet certified only to EN 12492 meets the climbing standard but not the industrial one US job sites require. Every helmet on this list carries ANSI Z89.1, and the Petzl models add EN 12492 on top of it.

Should I buy a vented or non-vented safety helmet?

Buy vented if you do not work near energized conductors and heat is a problem, such as on a summer steel deck or tower. Buy non-vented if electrical exposure is possible at all: only a non-vented shell can carry Class E, which is tested to 20,000 volts. The Klein Tools Type-2 Class E and the non-vented MSA V-Gard H2 are the choices for that work.