Best Coil Siding Nailers (2026) and the 15° Coil Nails That Fit
Buy the Bostitch N66C; step up to the Metabo HPT NV65AH2 for daily fiber-cement work
These picks were not tested. They come from the makers’ specifications, manuals and installation documents. Five criteria decided them. First, maximum nail length: 2-1/2 in. lets one tool drive the 2 in. nails that fiber-cement siding calls for and still have room for fence pickets on 2x rails. Second, whether the tool takes both wire-weld and plastic-sheet coils. Third, the shortest nail it accepts. Fourth, its weight. Fifth, how much air it uses.
The Bostitch N66C coil siding nailer is the one to buy for most homeowners, fence builders and remodelers. Bostitch’s page for it lists the model as the N66C-1, a 1-1/4-inch to 2-1/2-inch coil siding nailer with an aluminum housing. Bostitch’s description says it drives 15° wire-weld or plastic-inserted coil nails. That 1-1/4 in. minimum matches the DeWalt and Senco and goes 1/4 in. shorter than the Metabo HPT’s 1-1/2 in. It takes short shingle and trim nails at one end and 2-1/2 in. nails for 5/8 in. pickets on 2x rails at the other. Because it takes both collations, you can load whichever coil the yard has.
Get Bostitch N66C coil siding nailerWho should not buy it: anyone hanging vinyl siding. The vinyl section further down explains why a .092 in. siding nail is the wrong fastener for vinyl. A crew that blind-nails fiber-cement lap siding all day should look at the Metabo HPT NV65AH2 instead. Metabo HPT documents a switch between sequential and contact firing on that tool, plus an included no-mar nose cap. Both matter on prefinished plank. What is not worth the money is paying more for a different badge on the same range and collation. The DeWalt comparison below covers that.
Metabo HPT NV65AH2 vs Bostitch N66C vs DeWalt DW66C-1 vs Senco SN71P1
The Metabo HPT NV65AH2 coil siding nailer wins for fiber-cement installers. Metabo HPT says it drives nails up to 2-1/2 in. x .099 in. at 3 nails per second and that its coil holder takes up to 300 nails; its manual adds that .099 in. x 2-1/2 in. nails cannot be driven in some cases, depending on the material, and says to test-drive a few first. Its selective actuation switch moves between sequential and contact nailing. The tool card lists tool-less depth-of-drive adjustment and a plastic shield that deflects the spent wire collation. The NV65AH2 manual gives 4.9 lbs, a 70-120 psi operating range and a body of 11-27/64 x 11-13/16 x 5-1/8 in. Metabo HPT’s 2023 pneumatic catalog, like its NV65AH2 tool card, adds a detail the product page’s spec table gives differently. It lists the collation as wire at 16° and plastic at 15°, with a shank range of .090-.099 in. So .082 in. or .083 in. coils are outside what Metabo HPT lists for this tool. Its catalog also lists a No Mar Nose Cap (878344) in the box. Against the Bostitch, it gives up the shortest nails and a little shank range. In return you get the documented firing-mode switch and the nose cap.
Get Metabo HPT NV65AH2 coil siding nailer Get Metabo HPT Coil Siding NailsThe DeWalt DW66C-1 siding and fencing nailer is the one most buyers do not need. DeWalt’s manual gives 4.9 lb, 11-5/8 in. tall x 4-5/8 in. wide x 10-1/2 in. long, a 15° magazine and 70-120 psig. DeWalt lists a 1-1/4 to 2-1/2 in. range, wire-weld and plastic-inserted collation, a tool-free adjustable exhaust and a tool-free rafter hook; its manual warns never to use the rafter hook to hang the tool from your body, clothing or belt. DeWalt’s published nail range and collation are identical to the Bostitch’s. Buy the DeWalt when a DeWalt service center is the one near you. On the published specifications, the main difference is the tool-free adjustable rafter hook DeWalt lists, which Bostitch’s page does not mention.
Get DeWalt DW66C-1 siding and fencing nailerThe Senco SN71P1 is the specialist, and Senco publishes an MSRP of $419 for it. Senco lists dual wire or plastic collation, 1-1/4 to 2-1/2 in. nails, tool-free depth of drive, a rotatable rafter hook and a magazine of up to 375 nails. Its catalog gives 70-120 psi, 4.6 scfm at 60 cycles per minute and a 3/8 in. NPT air inlet. The 375-nail magazine means fewer reloads on long courses. The 3/8 in. inlet may need a different fitting from the coupler on your hose; Metabo HPT also lists a 3/8 in. inlet for the NV65AH2. For a production siding crew the extra capacity pays back. Senco’s manual says its selective (contact-capable) actuation is for experienced professionals only and strongly recommends sequential firing for less experienced users. For a fence or a single re-side, it is not worth the extra money over the Bostitch.
Wire-weld or plastic-sheet coils, and the 15°/16° label
A 15° coil siding nail comes in one of two collations. Wire-weld coils join the nails with two thin wires welded to the shanks. Plastic-sheet coils hold them in a plastic carrier strip. Grip-Rite makes both and publishes a technical data sheet for each, so neither is a fringe format. In practice the difference is what flies off the nose. Spent wire breaks into short fragments, which is why Metabo HPT fits the NV65AH2 with a shield to deflect them; its manual says not to remove that dust cover, because wire collation fragments can fly out. Plastic breaks into chips that land on the wall or the lawn. DeWalt’s manual calls for ANSI Z87.1 eye protection and ANSI S12.6 hearing protection with either kind, and Metabo HPT and Senco both say the operator and everyone else in the work area must wear ANSI Z87.1 safety glasses with side shields.
It matters at purchase because a wire-only nailer locks you into wire coils. All four tools above take both, by their makers’ own descriptions: the Bostitch N66C-1, Metabo HPT NV65AH2, DeWalt DW66C-1 and Senco SN71P1. So the collation decision moves to the nail box. Grip-Rite notes that each of its collated-fastener labels lists the tool makes and models the coil fits. Match the box to your tool by that list, not by the angle printed on the front.
The angle label is the one place makers disagree on paper. Metabo HPT’s catalog lists the NV65AH2’s wire collation as 16°. Metabo HPT’s page for its 13363HPT nails calls them 15° wire coil siding nails. Its page for the 1-1/2 in. 13362HPT calls that coil 16°. For the NV65AH2, Metabo HPT’s manual goes further: use only genuine Metabo HPT nails, because other nails can cause tool malfunction or nail breakdown leading to serious injury.
Length and shank: what 2 in. and 2-1/2 in. actually cover
Maximum length is what separates a siding nailer from tools that look like it. James Hardie’s installation instructions for HardiePlank lap siding call for a siding nail of 0.09 in. shank x 0.221 in. head x 2 in. long when blind-nailing to wood framing. The product data also lists a 6d siding nail at .093 x .222 x 2 in. and a 6d common at .113 x .267 x 2 in. Those .113 in. 6d commons are thicker than the .099 in. ceiling Metabo HPT publishes for the NV65AH2 and the .092 in. ceiling Senco publishes for the SN71P1. With a coil siding nailer, the 2 in. x .09 in. siding nail is the one to plan on. All of the tools above drive it with room to spare.
Fencing is where 2-1/2 in. earns its keep. A 2 in. nail through a 5/8 in. picket leaves 1-3/8 in. in the rail. A 2-1/2 in. nail through a 3/4 in. board on a 2x4 leaves 1-3/4 in. For a 5/8 in. picket on a 1-1/2 in. rail, that 2-1/2 in. nail is long enough to come out the back face. Measure your board stack before buying the coil, not the tool. Every nailer here reaches 2-1/2 in. with wire coils (Metabo HPT lists plastic coils only to 2-1/4 in. for the NV65AH2), so length mostly decides the nails.
At the short end, the Bostitch, DeWalt and Senco all start at 1-1/4 in. That covers short shingle and trim nails. On thin material, a nail longer than the stack only adds blow-through and splitting. Shank diameter matters too: Grip-Rite’s 15° wire-weld data sheet lists its coil siding nails at .080 in. to .092 in., with .092 in. offered at 1-3/4 in., 2 in. and 2-1/2 in., and .099 in. coils from 2 in. up. A thicker shank holds better in the rail but splits thin cedar more easily.
The 15° coil nails to load, by siding and fence material
Finish is decided by what the nail goes into, and the rules are written down. The International Residential Code, section R317.3.1, covers fasteners in preservative-treated wood. It accepts hot-dipped zinc-coated galvanized steel, stainless steel, silicon bronze or copper. Grip-Rite’s data sheet says its electrogalvanized nails, made to ASTM A641 Class 1, are not for cedar, cement board, redwood, most treated wood or exposed applications. The same Grip-Rite catalog names stainless steel as the only recommended fastener for redwood and cedar. James Hardie’s installation instructions recommend quality hot-dipped galvanized nails, and stainless fasteners near the ocean, large bodies of water or in very humid climates, and its fastening bulletin requires corrosion-resistant fasteners, galvanized or stainless.
For wood siding over sheathing, treated fence rails and general exterior work, buy the Metabo HPT Coil Siding Nails sold as model 13363HPT. Metabo HPT’s page for the 13363HPT describes a 15° full round head, ring shank, hot-dipped galvanized wire-coil siding nail, 1-3/4 in. x .092 in., in a box of 3,600. Metabo HPT lists siding, sheathing, decking and fencing as the jobs for it. Ring shank is the right call here. The annular rings resist the withdrawal that wood movement and wind load put on siding and pickets. It is also the coil Metabo HPT documents for its own NV65AH2. Metabo HPT also makes a 2 in. hot-dipped ring-shank version, 13365HHPT, and a 2 in. smooth-shank hot-dipped version, 13364HPT.
The one to avoid outdoors is the cheapest coating. The Freeman electrogalvanized ring shank coil siding nails are 15°, 1-3/4 in., wire collated and 3,600 to the box, by Freeman’s own description. Electrogalvanizing is the thin plated finish Grip-Rite rules out for treated wood, cedar, redwood and cement board. Use them for wall sheathing and covered, untreated work, not for a fence or Hardie plank.
Get Freeman electrogalvanized ring shank coil siding nailsWhy a coil roofing nailer is the wrong buy for siding and fences
A coil roofing nailer also fires 15° coils, which is why it looks like a cheaper siding tool. The numbers say otherwise. Senco’s catalog lists its RoofPro 445XP roofing nailer at 3/4 in. to 1-3/4 in. with .120 in. shank nails. That 1-3/4 in. ceiling falls short of the 2 in. nail Hardie specifies for blind-nailing with siding nails. It also falls short of the 2 to 2-1/2 in. most picket-to-rail fastening needs. The fat .120 in. shank and wide roofing head split thin cedar bevel siding and pickets, and they leave a visible head on any face-nailed board.
Hardie’s own fastener chart is the one exception. It lists an 11 ga. roofing nail, 0.121 in. shank x 0.371 in. head x 1.25 in. long, for blind-nailing HardiePlank to wood framing. A roofer who already owns a roofing nailer can blind-nail fiber-cement lap with it. But that same tool cannot face-nail trim, build a fence or reach 2 in. into framing through thick foam. If siding and fencing are the jobs you are buying for, the siding nailer is the tool.
Vinyl siding works the other way, and neither nailer is a clean answer. The Vinyl Siding Institute’s installation manual calls for corrosion-resistant nails at least 1-1/2 in. long, with a head at least 5/16 in. across and a 1/8 in. (0.125 in.) shank, long enough to penetrate sheathing, other nailable substrate and framing a total of at least 1-1/4 in.. A .092 in. siding nail is well under that shank figure. Vinyl siding is the one reason not to buy any of the siding nailers above. Use the fastener your vinyl maker’s instructions name.
Ownership, upkeep and the failures buyers hit
Metabo HPT, DeWalt and Senco each publish a 70-120 psi range, and Metabo HPT and DeWalt state 120 psi as the maximum; all three warn never to connect the tool to an air supply that can exceed 200 psi if a regulator fails. Hardie’s instructions say not to overdrive nail heads or drive nails at an angle, and to fill a countersunk nail hole and add a nail. Set pressure toward the low end, test on scrap, then disconnect the air supply and remove the nails before fine-tuning with the tool-free depth adjustment that Metabo HPT, DeWalt and Senco all document; all three manuals require disconnecting the air before any adjustment. Wood siding is softer than fiber cement and needs a shallower setting. If you switch materials mid-job, re-test. The makers’ manuals also set hard limits: never power the tool with oxygen or other bottled gas, never use it near flammable gases, liquids or combustible dust, keep bystanders and children away, and do not use it while tired or under the influence of drugs, alcohol or medication (Metabo HPT, DeWalt, Senco). Metabo HPT says to keep hands and feet at least 8 in. from the firing head. In contact mode, all three warn that recoil can drive an unwanted second nail. DeWalt says not to carry the tool up ladders, stairs or scaffolding with the air connected, and Senco says its tool is not insulated and must not be used where contact with electric power is possible.
Air supply limits pace. Senco publishes 4.6 scfm at 60 cycles per minute for the SN71P1, which is a steady production rate. Fence work, with pauses to move along the rail, uses far less air. Hose fittings are a practical snag. The SN71P1 has a 3/8 in. NPT inlet, so check your couplers before the first day on site. Metabo HPT, DeWalt and Senco all require hose rated for at least 150 psi and a coupling that releases all pressure from the tool when disconnected; Metabo HPT says never to use a non-relieving coupler.
Metabo HPT, DeWalt and Senco all say to disconnect the air supply before clearing a jam, and Metabo HPT adds to remove all remaining nails first. Load only coils inside the tool’s published shank range; for the NV65AH2, that range is .090-.099 in., and Senco says the SN71P1 will not accept Type S (narrow) plastic carrier strip. Spent wire collation fragments can fly out of the tool, which is why Metabo HPT says not to remove the NV65AH2’s dust cover. Plastic-sheet coils swap wire fragments for plastic chips, so pick the coil type you would rather sweep up.
Related guides
- 21° vs 30° Framing Nailers: Match the Angle, Collation and Nails
- Best ATV/UTV Tool Boxes and Cargo Racks (2026): For Farm and Ranch Work
- Best Balaclavas and Neck Gaiters for Cold Work
- Best Bib Overalls for Construction and Cold-Weather Work (2026)
- Best Paslode Fuel Cells and Nail Packs for Framing Nailers
FAQ
Do I need wire-weld or plastic-sheet coil nails for a 15° siding nailer?
Either works in all four nailers discussed here. Bostitch, Metabo HPT, DeWalt and Senco each say their tool takes both wire and plastic collation. Pick by the tool list printed on the nail box, which Grip-Rite says appears on each of its collated-fastener labels. Wire leaves metal fragments and plastic leaves chips.
Can I use electrogalvanized coil nails on a pressure-treated or cedar fence?
No. IRC section R317.3.1 requires hot-dipped galvanized, stainless steel, silicon bronze or copper fasteners in preservative-treated wood. Grip-Rite says its electrogalvanized nails are not for cedar, redwood, cement board or most treated wood. Use hot-dipped galvanized ring shank on treated rails and stainless on cedar or redwood.
Will a coil siding nailer work for vinyl siding?
Not with standard coil siding nails. The Vinyl Siding Institute’s manual calls for a 1/8 in. shank and a head at least 5/16 in. across. A .092 in. coil siding nail falls well short of that shank size. Follow the fastener your vinyl maker’s installation instructions name.